professional factory for 260t Open Front Single Point Press Machine - Pull Down High Speed Press (HX series) – Daya
professional factory for 260t Open Front Single Point Press Machine - Pull Down High Speed Press (HX series) – Daya Detail:
DAYA straight side double crank punch press
VS
Other straight side double crank presses
Daya press
Daya press: with platform and safety fence, convenient for clutch maintenance and change of cooling oil, main motor belt is loose and easy to adjust, and convenient for subsequent maintenance. Safer and more convenient.
Other press
Other press: Without maintenance platform. Clutch maintenance, replacement of cooling oil, loose adjustment of main motor belt, etc. which can only be completed with the assistance of forklift, which is not convenient for subsequent repair and maintenance. There are some potential safety hazards.
Daya press
Daya press: Daya press adopts four corners and eight sides to surround the guide rail. In the stamping forming position, the slide guide rail is included by all the guide rails on the table body. This kind of guide rail has the characteristics of high stamping accuracy, strong anti eccentric load capacity, small rail wear and long precision retention time.
Other press
Other press: the guide rail with semi enclosed structure as shown in the right figure is adopted. During the stamping process, there is a section of guide rail exposed. During the stamping process, the slide guide rail is easy to tilt, with poor anti bias load capacity, large rail wear, short precision retention time and high maintenance cost.
Daya press
Daya press: the distance between the two points of force application is more than 60%; Advantages: the larger the distance between the two force application points, the greater the eccentric bearing capacity; the larger the distance between the two force application points, the higher the design cost.
Other press
Other press: the distance between the two points is generally less than 50%; Disadvantages: the smaller the distance between the two force application points, the smaller the eccentric bearing capacity. The guide rail is easy to tilt, the guide way is easy to wear, and the precision of guide rail is poor.
Daya press
Daya press: forced thin oil circulation system, energy saving, can be recycled, fan thermal performance is good, compared with grease lubrication can be increased by 5-10 beats per minute.
Other press
Other press: electric grease pump, grease can not be reused, no advantage of forced thin oil circulation system.
Daya press
Daya press: when the stroke length is the same, the forced thin oil circulation system has higher efficiency, compared with grease lubrication, it can increase 5-10 beats per minute. Strictly follow the Japanese JIS level 1 standard; the Japanese JIS level 1 standard is higher than the Taiwan CNS level 1 standard.
Other press
Other press:electric grease pump, grease can not be reused, no forced oil circulation system advantages. according to Taiwan CNS level 1 standard
Slide guide of Daya punch press
VS
other slide guides of punch
Daya press
Other press
Guide rail of Daya punch press
1.High frequency quenching process: hardness above hrc48;
2. Grinding process of guide rail: the surface finish can reach ra0.4-ra0.8 (mirror surface), flatness, parallelism and verticality within 0.005mm/ ㎡.
3.The machine tool has the advantages of small wear, high precision, long precision maintenance time, long service life and low energy consumption.
Other press guide railno quenching process; milling processing, surface roughness ra1.6-ra3.2, flatness, parallelism, perpendicularity more than 0.3mm / ㎡
Daya press crankshaft
VS
other press crankshafts
Daya punch press: the crankshaft is made of high strength alloy 42CrMo Advantages: the strength is 1.3 times higher than that of 45 steel, the service life is long, the wear resistance is good, the wear is small, and the precision is maintained for a long time.
Other presses: made of 45 steel, Disadvantages: low cost，the strength and wear resistance are not comparable to 42CrMo
Daya
Oil way of DAYA punch PRESS: Φ 8 is used for oil pressure lubrication piping.
Advantages: long pipeline, large diameter is not easy to block, break, ensure the safety of lubricating oil, smooth.
Other
Other presses: the oil pressure lubrication piping of press adopts Φ 6.
Product detail pictures:
Related Product Guide:
We always stick to the principle "Quality First, Prestige Supreme". We are fully committed to providing our clients with competitively priced quality products, prompt delivery and professional service for professional factory for 260t Open Front Single Point Press Machine - Pull Down High Speed Press (HX series) – Daya , The product will supply to all over the world, such as: Australia, Frankfurt, Johor, Based on products and solutions with high quality, competitive price, and our full range service, we have accumulated experienced strength and experience, and we've built up a very good reputation in the field. Along with the continuous development, we commit ourselves not only to the Chinese domestic business but also the international market. May you moved by our high quality items and passionate service. Let's open a new chapter of mutual benefit and double win.
By Dinah from Jamaica - 2018.04.25 16:46
The factory has advanced equipment, experienced staffs and good management level, so product quality had assurance, this cooperation is very relaxed and happy!
By Candy from Croatia - 2018.06.26 19:27
Products categories
-
China wholesale Water Cooling - Frequency Conv...
-
Cheap PriceList for 600t Straight Double Point ...
-
China Manufacturer for 200t C Frame Single Poin...
-
Factory Price For Pneumatic Drill Manufacturer ...
-
Discount Price 500t Mechanical Punch Machine -...
-
Factory Outlets China High Speed Feeder - High...